Glycol dehydration units are everywhere in US gas production, and almost every one of them has the same side effect: the still column vents a stream rich in benzene, toluene, ethylbenzene and xylene. These BTEX compounds are hazardous air pollutants, and regulators at the federal and state level continue to tighten how much can leave a facility. For operations managers and environmental compliance teams, 2026 is a year where reliable BTEX control is less of an option and more of a baseline expectation.
Where BTEX Comes From on a Production Site
Triethylene glycol (TEG) absorbs water from natural gas, but it also absorbs aromatic hydrocarbons. When the rich glycol is heated in the reboiler to drive off water, those aromatics leave with the still vent vapor. Flash tank off gas can also carry BTEX, though usually at lower concentrations. Without control, that still vent goes straight to atmosphere.
Factors that increase BTEX emissions include high glycol circulation rates, rich gas compositions, warm inlet gas and poorly tuned reboilers. Simply optimizing glycol circulation can reduce emissions noticeably before any control equipment is added.
How BTEX Control Systems Work
Most BTEX Control Systems follow a similar sequence. The still vent vapor is routed to a condenser, often air cooled, where water and heavier hydrocarbons drop out as liquid. The remaining non condensable vapor is then sent to a combustion device such as a burner in the reboiler firebox, an enclosed combustor or a flare, where the BTEX is destroyed.
Condensation Stage
The condenser does the heavy lifting on volume. By cooling the still vent stream, it knocks out most of the water vapor and a large share of the aromatics. Collected liquids go to a separator and then to storage or disposal. Condenser sizing must account for summer ambient temperatures, since a warm afternoon in West Texas can reduce performance significantly.
Combustion Stage
Non condensables still contain BTEX and methane. Routing them to a properly designed burner achieves high destruction efficiency. Forced draft designs use a blower to supply combustion air, which improves mixing and makes destruction more consistent across changing flow rates. This is especially helpful when the still vent rate swings with gas throughput.
Regulatory Drivers in 2026
Federal NESHAP HH and HHH rules set BTEX limits for glycol dehydrators at major and area sources. State programs in Colorado, New Mexico, Texas and Pennsylvania add their own requirements and reporting. Methane rules under EPA OOOOb also push operators to control the hydrocarbon content of these vent streams. Compliance teams should confirm which thresholds apply to each dehydrator, since benzene emissions above certain levels trigger control requirements.
- Track annual benzene and total BTEX estimates using approved calculation tools.
- Keep records of condenser outlet temperatures and combustion device operation.
- Document pilot or flame monitoring on the combustion device.
- Schedule periodic inspections and keep maintenance logs ready for audits.
Choosing the Right Configuration
There is no single best BTEX package. Engineers should consider:
- Still vent flow and composition, from simulation or field sampling.
- Ambient conditions, which affect condenser performance.
- Available fuel gas for pilots and assist firing.
- Power availability if a forced draft blower or controls are used.
- Back pressure limits on the still column, since too much back pressure hurts glycol regeneration.
Some sites route non condensables to an existing enclosed combustor that also handles tank vapors. Others need a dedicated unit. Working with a supplier like Hero Process Solutions, which designs combustion equipment, vapor handling and process systems together, helps avoid mismatched components that underperform in the field.
Operating and Maintenance Tips
BTEX systems are simple, but small problems add up. Condensers foul with dust and debris, so fin cleaning should be part of routine site visits. Liquid drains can freeze in winter, causing liquid to back up into the combustion device. Pilots and igniters need regular checks, and flame arresters should be inspected for plugging. A short monthly checklist goes a long way toward keeping destruction efficiency high and avoiding deviation reports.
Frequently Asked Questions
What does BTEX stand for?
BTEX stands for benzene, toluene, ethylbenzene and xylene. These aromatic hydrocarbons are classed as hazardous air pollutants. Benzene in particular is a known carcinogen, which is why regulators focus on it.
Can I reduce BTEX without new equipment?
Optimizing glycol circulation rate is often the first step and can reduce emissions meaningfully. Tuning the reboiler and flash tank operation helps too. However, many sites still need a condenser and combustion device to meet limits.
What is a forced draft BTEX system?
A forced draft system uses a blower to push combustion air into the burner. This gives better mixing and more stable destruction across varying flows. It requires electrical power on site.
How often should BTEX systems be inspected?
Monthly visual checks are a good practice, with more detailed inspections at least annually. Permit conditions may require specific monitoring intervals. Keeping logs makes audits much easier.
